bc10/有機EL

bc10

有機EL †

モデル名 †

• P0430WQL

メカニカルデータ †

接続コネクタ †

• 推奨コネクタ
  • FH26-71S-03SHAW (ヒロセ電機製)

• ピン配置

  ピン番号	機能名	備考
  1	TP1	タッチパネル (X-)
  2	TP2	タッチパネル (Y-)
  3	TP3	タッチパネル (X+)
  4	TP4	タッチパネル (Y+)
  5	AR_VSS	LED駆動電源(-)
  6	AR_VSS
  7	TEST1_VS	オープン (テスト用端子)
  8	AR_VDD	LED駆動電源(+)
  9	AR_VDD
  10	TEST2_VD	オープン
  11	ARREF	Panel refers voltage of the regulator ARREF or external input voltage. (-8V~+8V)
  12	VGL	Low Voltage output of regulator VGL or external input voltage. (-3V~-8V)
  13	VGH	High Voltage output of regulator VGH or external input voltage. (+3V~+8V)
  14	LVO	Negative output voltage of the booster2. (-8.5V)
  15	C22N	Connect to the step-up circuit, capacitors according to the step-up factor. Leave this pin open if the internal step-up circuit is not used.
  16	C22P
  17	HVO	Positive output voltage of the booster2. (8.5V)
  18	C21P	Connect to the step-up circuit, capacitors according to the step-up factor. Leave this pin open if the internal step-up circuit is not used.
  19	C21N
  20	C11N	Connect to the step-up circuit, 4capacitors according to the step-up factor. Leave this pin open if the internal step-up circuit is not used.
  21	C11P
  22	C12N
  23	C12P
  24	PVSS	Charge pump ground pin, it must connect to external ground.
  25	DDVDH	Output voltage of the booster1. (5.1V/6.0V)
  26	VSSA	Analog ground pin. It must connect to external ground.
  27	VSSA
  28	VCI	A power supply for the Analog circuit. (3.0V~3.6V)
  29	VCI
  30	VGAM1OUT	Output voltage of the VGAM1OUT regulator and used positive power of source driver. (4.8V/5.8V)
  31	VDDD	Internal logic voltage input or output pin
  32	VCC	A power supply for the Digital circuit. (1.5V~3.6V)
  33	VSSD	Digital ground pin. It must connect to external ground.
  34	NRESET	Reset pin. Setting either pin low initializes the LSI. Must be reset after power is supplied. (Normally pull high)
  35	NCS	Serial Interface chip enable pin. (Normally pull high)
  36	SCL	Serial Interface clock input pin. (Normally pull high)
  37	SDA	Serial Interface data line. (Normally pull high)
  38	DE	Data enable
  39	VSYNC	Frame synchronizing signal.
  40	HSYNC	Line synchronizing signal.
  41	DCLK	Dot clock signal.
  42	D27	Digital data input. DX0 is LSB and DX7 is MSB.
  43	D26
  44	D25
  45	D24
  46	D23
  47	D22
  48	D21
  49	D20
  50	D17
  51	D16
  52	D15
  53	D14
  54	D13
  55	D12
  56	D11
  57	D10
  58	D07
  59	D06
  60	D05
  61	D04
  62	D03
  63	D02
  64	D01
  65	D00
  66	TEST3_W	オープン (テスト用端子)
  67	AR_VDD	LED駆動電源(+)
  68	AR_VDD
  69	AR_VSS	LED駆動電源(-)
  70	AR_VSS
  71	TEST4_P	オープン (テスト用端子)

※ D00〜D27: bc10で利用しているパラレルモードでは D0X=Rx, D1X=Gx, D2X=Bx に割り当てられます。

参考情報 †

詳細については、下記のURLからデータシートがダウンロードできますので、そちらを参照してください。

• 有機ELパネル
  • http://d1.ourdev.cn/bbs_upload603362/files_25/ourdev_532127.pdf
  • http://www.alldatasheet.com/datasheet-pdf/pdf/317965/AZDISPLAYS/P0430WQLB-T.html
• 内蔵コントローラ HX5116-A (Himax Technologies, Inc.)
  
  • http://www.andilcd.de/medien/de/download/controller/andilcd_conoled_sheet_de_hx5116.pdf