DIY Electronics/AMI602 Breakout Module
[
Front page
] [
New
|
List of pages
|
Search
|
Recent changes
]
Start:
[[DIY Electronics]]
-Contents
#contents
*Summary [#f0a0b25e]
>
This section discusses applications of AMI602 (G² mo...
AMI602 is a product of Aichi Micro Intelligent Corp. The ...
for better handling. AMI602 can be easily accessed from P...
by I²C path. In this section, two examples are intro...
microcontroller, and the other is to make the module beco...
-Manual of AMI 602 Breakout module (in Japanese &ref("ami...
-Data sheet of AMI 602 (in English &ref("ami602e.pdf");)~
>
Please do not contact with Aichi Micro Intelligent Corp f...
company does not support AMI602 Breakout module. (AMI602 ...
BeatCraft, Inc. If there are any questions and concerns, ...
*** About VID voltage [#kae9f3e8]
>
- Extra information form Aichi Micro Intelligent Corp.~
According to the recommended operating conditions listed...
recommended operating condition of VID is from 1.65~VDD ...
that the some products use the sensors at the range betw...
It is true that a sample schematic diagram notes VID = ...
Micoro Intelligent's office have worked well at VID = 3....
at such level of voltage , it will be considered as outs...
Since the absolute maximum ratings of the sensor are bet...
not brake down immediately. However, it will not work co...
using the sensor.
** A sample with PIC 24FJ64 GA002 [#bea7b7cf]
>
-Schematic Diagram
-- PDF &ref("bc10-002-0001.pdf");
-- OrCAD &ref("BC10-002-0001.DSN");
--- On the schematic diagram, DNI indicates that parts ar...
when the fluctuations of low frequency, which is generate...
--- C10 and C11are electrolytic capacitors, and other cap...
C3 should be the same type of capacitor as X5R or X7R .
--- The early version of PIC 24FJ64 GA002 cannot communic...
--- In some LCD character displays, Vss is defined as Vdd...
using some LED character display other than SC2004CS.disp...
--- To use backlit LCD character display, please be caref...
>
- Sample Source Program &ref("MPLAB.zip");
-- This program uses MPLAB IDE and MPLAB C Compiler for ...
-- PICkit3 is employed as a debugger.
--- Register and compile the source file, which is create...
into the PIC.
--- The sample program is quite simple. Initialize the se...
--- The serial port says 11500 bps, 8bit, None party, No ...
messages.
** A Sample with Arduino [#k4b9c1f1]
>
- Schematic Diagram
AMI602 Breakout -> Pin # of Arduino
AMI602 1: -> Arduino A5
AMI602 2: -> 2V (generated from 5V by power circui...
AMI602 3: -> Arduino A4
AMI602 4: -> Arduino D4
AMI602 6: -> Arduino D6
AMI602 7: -> Arduino D7
AMI602 9: -> Arduino GND
AMI602 10: -> Arduino 3V3
>
VID of AMI602 is from 1.65 V to 2.4 V, the level shift is...
~
#ref(./AMI602_sch.png,50%);
~
- Sample Source Programs
-- Arduino side &ref("AMI602_20100708.zip");
--- Decompress the file, open up the decompressed file in...
~
-- Processing side &ref("AMI602PC_20100708.zip");
--- Unzip the file, open up the file in processing. Then ...
--- Use this file with the sample of Arduino side (AMI602...
--- To Depend on its environment, change the configuratio...
--- To utilize the outputs of 3-axis magnetometer, the pr...
~
#youtube(uLPEP_BlK5s,left);
~
** AMI602 Arduino Shield [#dc8d2e06]
#ref(./AMI602_SHIELD.jpg,100%);
** List of AMI602 Arduino Shield parts [#zf43b912]
#ref(./AMI602parts.jpg,35%);
>>>(Click for larger image)~
LEFT:
|No.|Name|Quantity|h
|CENTER:1|Ceramic Capacitor 0.1μF |CENTER:1|
|CENTER:2|Regulator LM317LZ |CENTER:1|
|CENTER:3|Capacitor 1μF |CENTER:1|
|CENTER:4|Resistor 10KΩ |CENTER:6|
|CENTER:5|Resistor 5.1KΩ |CENTER:1|
|CENTER:6|Resistor 2.4KΩ |CENTER:1|
|CENTER:7|Resistor 1.5KΩ |CENTER:2|
|CENTER:8|Resistor 1KΩ |CENTER:2|
|CENTER:9|Resistor 330Ω |CENTER:1|
|CENTER:10|MOSFET BSS123 |CENTER:3|
|CENTER:11|Pin Header 40x1 2.54mm |CENTER:1|
|CENTER:12|Shield Body |CENTER:1|
* Reference [#p82bc609]
- Aichi Micro Intelligent Corp homepage (in Japanese)
--http://www.aichi-mi.com/index.html
* Reference History [#zbda35bc]
>
2010/08/26 This article is initially uploaded.~
2010/09/27 The information of AMI 602 based Arduino shiel...
End:
[[DIY Electronics]]
-Contents
#contents
*Summary [#f0a0b25e]
>
This section discusses applications of AMI602 (G² mo...
AMI602 is a product of Aichi Micro Intelligent Corp. The ...
for better handling. AMI602 can be easily accessed from P...
by I²C path. In this section, two examples are intro...
microcontroller, and the other is to make the module beco...
-Manual of AMI 602 Breakout module (in Japanese &ref("ami...
-Data sheet of AMI 602 (in English &ref("ami602e.pdf");)~
>
Please do not contact with Aichi Micro Intelligent Corp f...
company does not support AMI602 Breakout module. (AMI602 ...
BeatCraft, Inc. If there are any questions and concerns, ...
*** About VID voltage [#kae9f3e8]
>
- Extra information form Aichi Micro Intelligent Corp.~
According to the recommended operating conditions listed...
recommended operating condition of VID is from 1.65~VDD ...
that the some products use the sensors at the range betw...
It is true that a sample schematic diagram notes VID = ...
Micoro Intelligent's office have worked well at VID = 3....
at such level of voltage , it will be considered as outs...
Since the absolute maximum ratings of the sensor are bet...
not brake down immediately. However, it will not work co...
using the sensor.
** A sample with PIC 24FJ64 GA002 [#bea7b7cf]
>
-Schematic Diagram
-- PDF &ref("bc10-002-0001.pdf");
-- OrCAD &ref("BC10-002-0001.DSN");
--- On the schematic diagram, DNI indicates that parts ar...
when the fluctuations of low frequency, which is generate...
--- C10 and C11are electrolytic capacitors, and other cap...
C3 should be the same type of capacitor as X5R or X7R .
--- The early version of PIC 24FJ64 GA002 cannot communic...
--- In some LCD character displays, Vss is defined as Vdd...
using some LED character display other than SC2004CS.disp...
--- To use backlit LCD character display, please be caref...
>
- Sample Source Program &ref("MPLAB.zip");
-- This program uses MPLAB IDE and MPLAB C Compiler for ...
-- PICkit3 is employed as a debugger.
--- Register and compile the source file, which is create...
into the PIC.
--- The sample program is quite simple. Initialize the se...
--- The serial port says 11500 bps, 8bit, None party, No ...
messages.
** A Sample with Arduino [#k4b9c1f1]
>
- Schematic Diagram
AMI602 Breakout -> Pin # of Arduino
AMI602 1: -> Arduino A5
AMI602 2: -> 2V (generated from 5V by power circui...
AMI602 3: -> Arduino A4
AMI602 4: -> Arduino D4
AMI602 6: -> Arduino D6
AMI602 7: -> Arduino D7
AMI602 9: -> Arduino GND
AMI602 10: -> Arduino 3V3
>
VID of AMI602 is from 1.65 V to 2.4 V, the level shift is...
~
#ref(./AMI602_sch.png,50%);
~
- Sample Source Programs
-- Arduino side &ref("AMI602_20100708.zip");
--- Decompress the file, open up the decompressed file in...
~
-- Processing side &ref("AMI602PC_20100708.zip");
--- Unzip the file, open up the file in processing. Then ...
--- Use this file with the sample of Arduino side (AMI602...
--- To Depend on its environment, change the configuratio...
--- To utilize the outputs of 3-axis magnetometer, the pr...
~
#youtube(uLPEP_BlK5s,left);
~
** AMI602 Arduino Shield [#dc8d2e06]
#ref(./AMI602_SHIELD.jpg,100%);
** List of AMI602 Arduino Shield parts [#zf43b912]
#ref(./AMI602parts.jpg,35%);
>>>(Click for larger image)~
LEFT:
|No.|Name|Quantity|h
|CENTER:1|Ceramic Capacitor 0.1μF |CENTER:1|
|CENTER:2|Regulator LM317LZ |CENTER:1|
|CENTER:3|Capacitor 1μF |CENTER:1|
|CENTER:4|Resistor 10KΩ |CENTER:6|
|CENTER:5|Resistor 5.1KΩ |CENTER:1|
|CENTER:6|Resistor 2.4KΩ |CENTER:1|
|CENTER:7|Resistor 1.5KΩ |CENTER:2|
|CENTER:8|Resistor 1KΩ |CENTER:2|
|CENTER:9|Resistor 330Ω |CENTER:1|
|CENTER:10|MOSFET BSS123 |CENTER:3|
|CENTER:11|Pin Header 40x1 2.54mm |CENTER:1|
|CENTER:12|Shield Body |CENTER:1|
* Reference [#p82bc609]
- Aichi Micro Intelligent Corp homepage (in Japanese)
--http://www.aichi-mi.com/index.html
* Reference History [#zbda35bc]
>
2010/08/26 This article is initially uploaded.~
2010/09/27 The information of AMI 602 based Arduino shiel...
Page: