BC-USB-Kit/get started
[
Front page
] [
New
|
List of pages
|
Search
|
Recent changes
]
Start:
[[labs.beatcraft.com]]~
[[BC-USB-Kit]]~
#contents
* BC-USB-Kit get started [#n36b6741]
>
This article provides the step-by-step explanations for h...
When you write your firmware into your BC-USB-Kit, please...
** Requirements [#v90827a2]
>
To complete the build and writing processes, the hardware...
~
- BC-USB-Kit~
No pin headers are attached to BC-USB-Kit. There are only...
&ref(001.png,,20%); &ref(001_Pk.png,,30%);~
~
- In-Circuit Debugger~
In-circuit Debugger is a tool for writing a firmware into...
~
- Firmware (for checking)~
The source code of a demo firmware, ?USB Device - CDC - S...
#ref(USB Device - CDC - Sensor.zip);~
This firmware can be used for checking the operational st...
~
- [[MPLAB X ICD:http://www.microchip.com/pagehandler/en-u...
This is an IDE for the PIC micro controller. It is used f...
~
- [[MPLAB XC Compilers:http://www.microchip.com/pagehandl...
In this article, Windows version of MPLAB X IDE and MPLAB...
If you use other platforms other than Windows, please app...
** Build the Firmware [#g863876d]
>
+ Expand the downloaded source code of the firmware, ?USB...
&ref(003_firmware.png,,50%);~
~
+ Start up X IDE.~
&ref(004_X_IDE_launch.png,,50%); &ref(005_X_IDE.png,,20%);~
~
+ From the menu of MPLAB X IDE, select File →Open P...
&ref(006_X_IDE_open.png,,20%);~
~
Open Up ?USB Device - CDC ? Sensor.X,? which is located a...
&ref(007_X_IDE_open.png,,20%); &ref(008_X_IDE_open.png,,4...
~
+ Once open up the project you will use, close Start Page...
&ref(010_X_IDE.png,,20%); &ref(011_X_IDE.png,,20%);~
~
From the menu of MPLAB X IDE, choose Run →Set Proj...
&ref(012_X_IDE_conf.png,,20%);~
~
As the Project Properties Window opens, configure Hardwar...
&ref(013_X_IDE_pp.png,,20%); &ref(014_X_IDE_pp.png,,30%);~
~
+ Once these configurations of Hardware Tool and Compiler...
&ref(015_X_IDE.png,,20%); &ref(016_X_IDE.png,,30%); &ref(...
~
+ Once the preparations are completed, to click the icon ...
&ref(018_X_IDE_build.png,,30%);~
~
As the execution log shows up in the tab of USB Device - ...
&ref(019_X_IDE_build.png,,20%);~
~
The name of the built firmware is ?USB_Device_-_CDC_-_Sen...
** Writing the firmware onto PIC [#n6ebf94a]
>
+ The build process of the firmware is completed, click t...
&ref(020_X_IDE_rp.png,,30%);~
~
The firmware is written into BC-USB-Kit by PICkit 3.~
While PICkit 3 writes the firmware into PIC, the color of...
The status of the writing process is appeared in the PICk...
&ref(021_X_IDE_rp.png,,20%);~
~
Programming...
Programming/Verify complete
When the status shown above appears in the tab, the writi...
~
If you click the icon of Make and Program Device (See the...
&ref(022_X_IDE_mp.png,,30%);~
~
- If the writing process is failed, pull off the USB cabl...
&ref(027_X_IDE.png,,40%);~
~
If the color of status LED at PICkit 3 turns to green, it...
Still the writing process is failed, please check the sol...
~
** Conforming operation of the firmware [#u22163e7]
+As BC-USB-Kit, which is the firmware is already written,...
&ref(023_driver.png,,30%); &ref(024_driver.png,,30%);~
~
+To open up the recognized COM port by TeraTerm at Baud r...
&ref(025_teraterm.png,,40%); &ref(026_teraterm.png,,40%);~
~
The contents of outputs are the read values of the humidi...
* Revision History [#h08d8e05]
>
- 2015/04/01 This document is initially published.
End:
[[labs.beatcraft.com]]~
[[BC-USB-Kit]]~
#contents
* BC-USB-Kit get started [#n36b6741]
>
This article provides the step-by-step explanations for h...
When you write your firmware into your BC-USB-Kit, please...
** Requirements [#v90827a2]
>
To complete the build and writing processes, the hardware...
~
- BC-USB-Kit~
No pin headers are attached to BC-USB-Kit. There are only...
&ref(001.png,,20%); &ref(001_Pk.png,,30%);~
~
- In-Circuit Debugger~
In-circuit Debugger is a tool for writing a firmware into...
~
- Firmware (for checking)~
The source code of a demo firmware, ?USB Device - CDC - S...
#ref(USB Device - CDC - Sensor.zip);~
This firmware can be used for checking the operational st...
~
- [[MPLAB X ICD:http://www.microchip.com/pagehandler/en-u...
This is an IDE for the PIC micro controller. It is used f...
~
- [[MPLAB XC Compilers:http://www.microchip.com/pagehandl...
In this article, Windows version of MPLAB X IDE and MPLAB...
If you use other platforms other than Windows, please app...
** Build the Firmware [#g863876d]
>
+ Expand the downloaded source code of the firmware, ?USB...
&ref(003_firmware.png,,50%);~
~
+ Start up X IDE.~
&ref(004_X_IDE_launch.png,,50%); &ref(005_X_IDE.png,,20%);~
~
+ From the menu of MPLAB X IDE, select File →Open P...
&ref(006_X_IDE_open.png,,20%);~
~
Open Up ?USB Device - CDC ? Sensor.X,? which is located a...
&ref(007_X_IDE_open.png,,20%); &ref(008_X_IDE_open.png,,4...
~
+ Once open up the project you will use, close Start Page...
&ref(010_X_IDE.png,,20%); &ref(011_X_IDE.png,,20%);~
~
From the menu of MPLAB X IDE, choose Run →Set Proj...
&ref(012_X_IDE_conf.png,,20%);~
~
As the Project Properties Window opens, configure Hardwar...
&ref(013_X_IDE_pp.png,,20%); &ref(014_X_IDE_pp.png,,30%);~
~
+ Once these configurations of Hardware Tool and Compiler...
&ref(015_X_IDE.png,,20%); &ref(016_X_IDE.png,,30%); &ref(...
~
+ Once the preparations are completed, to click the icon ...
&ref(018_X_IDE_build.png,,30%);~
~
As the execution log shows up in the tab of USB Device - ...
&ref(019_X_IDE_build.png,,20%);~
~
The name of the built firmware is ?USB_Device_-_CDC_-_Sen...
** Writing the firmware onto PIC [#n6ebf94a]
>
+ The build process of the firmware is completed, click t...
&ref(020_X_IDE_rp.png,,30%);~
~
The firmware is written into BC-USB-Kit by PICkit 3.~
While PICkit 3 writes the firmware into PIC, the color of...
The status of the writing process is appeared in the PICk...
&ref(021_X_IDE_rp.png,,20%);~
~
Programming...
Programming/Verify complete
When the status shown above appears in the tab, the writi...
~
If you click the icon of Make and Program Device (See the...
&ref(022_X_IDE_mp.png,,30%);~
~
- If the writing process is failed, pull off the USB cabl...
&ref(027_X_IDE.png,,40%);~
~
If the color of status LED at PICkit 3 turns to green, it...
Still the writing process is failed, please check the sol...
~
** Conforming operation of the firmware [#u22163e7]
+As BC-USB-Kit, which is the firmware is already written,...
&ref(023_driver.png,,30%); &ref(024_driver.png,,30%);~
~
+To open up the recognized COM port by TeraTerm at Baud r...
&ref(025_teraterm.png,,40%); &ref(026_teraterm.png,,40%);~
~
The contents of outputs are the read values of the humidi...
* Revision History [#h08d8e05]
>
- 2015/04/01 This document is initially published.
Page:
![[PukiWiki]](image/bc_logo.png "[PukiWiki]"){kind=logo}
