ANT/BC-ANT-SERIAL_2
[
Front page
] [
New
|
List of pages
|
Search
|
Recent changes
]
Start:
[[ANT]]
*BC-ANT-SERIAL [#l03c8002]
** 1. Overview [#m22dd705]
>
BC-ANT-SERIAL is a module that is equipped with nRF24AP2-...
>
&ref(DSCF7967r.JPG,,40%);~
※ ?100-yen coin is placed for the reference.
** 2. Specification [#iaa6231e]
>
- Absolute Maximum Ratings
||Minimum|Maximum|
|Supply Voltage (VDD)|-0.3V|+3.6V|
|GND Voltage (VSS)||0V|
|I/O Terminal Voltage|-0.3V|Less than 3.6V or VDD + 0.3V|
|Operation Temperature (No Condensation)|-40℃|+85&#...
|Storage Temperature (No Condensation)|-40℃|+85T...
>
- Operation Ratings
|Items|Minimum|Standard|Maximum|Unit ? Memo|
|Supply Voltage|1.9|3.0|3.6|V|
|H level Input Voltage|0.7 x VDD||VDD|V|
|L level Input Voltage|VSS||0.3 x VSS|V|
|H level Output Voltage|VDD ? 0.3||VDD|V|
|L level Output Voltage|VSS||0.3|V|
|Output Frequency|2403||2480|MHz (1MHz steps 78 waves)|
|PCB (Length)||26.5||mm|
|PCB (Width)||15||mm|
|PCB (Depth)||1||mm (Excluding parts)|
**3. Host Interface [#udec3c27]
>
To communicate with a microcontroler, BC-ANT-SERIAL suppo...
>
Assignment of pin-headers and pads are shown in the table...
>
- Assignment of Pin-Headers
|No.|Signal Type|Direction|Memo|
|1|VDD|Voltage|About Supply Voltage, Please look at ?2. S...
|2|GND|GND||
|3|RTS|Output|UART communication flow control|
|4|RX|Input|UART communication (Receiving at module side)|
|5|TX|Output|UART communication (Transmitting from module...
>
- Assignment of Pads
|Pad Name|Signal Type|Direction|Memo|
|RST|RESET|Input|Resetting ANT chip|
|SUP|SUSPEND|Input|Suspending ANT chip|
|SLP|SLEEP|Input|Sleeping ANT chip|
|BR1|BR1|Input|Configure UART communication speed1|
|BR2|BR2|Input|Configure UART communication speed2|
|BR3|BR3|Input|Configure UART communication speed3|
>
&ref(DSCF7962r2.JPG,,40%);
&ref(DSCF7963r2.JPG,,40%);~
>
The lines of RST, SUP, and SLP are used for tightly manag...
The lines of BR1, BR2, and BR3 are used for setting the s...
>
[Caution]~
In the picture, (a) is the connector, which is specifical...
In the picture, (b) is the chip antenna. To maintain the ...
***About Control Pads [#cce6d707]
>
The Size of RST, SUP, SLP, BR1, BR2, and BR3 pads is iden...
>
- RST
-- As ANT chip is electronically reset externally, this p...
>
- SUSPEND
-- This pad is used for suspending ANT chip. The line is ...
>
- SLEEP
-- This pad lets ANT chip sleep. This line is pulled-up t...
>
- BR1, BR2, and BR3
-- These lines are pulled-up to VDD. As no resistor is at...
>
-- Pads & Communication Speed
|BR1|BR2|BR3|Communication Speed (bps)|
|0|0|0|4800|
|0|0|1|38400|
|0|1|0|19200|
|0|1|1|50000|
|1|0|0|1200|
|1|0|1|9600|
|1|1|0|2400|
|1|1|1|57600|
0: 0Ω resistor is attached~
1: Non~
** How to Use [#u1755de7]
>
(1) How to connect with the serial communication (TXD, RX...
Pin-headers are attached at J1. Please look at Host Inter...
&ref(picture3.jpg,,60%);~
>
From ANT module, RTS is output for controlling hardware f...
>
(2) How to Connect Control Lines (Reset, Sleep, and Suspe...
&ref(picture4.jpg,,60%);~
~
To use the lines of RST (reset), SLP (sleep), and SUP (su...
>
- RST (reset)
-- When ANT is in operation, this line is at H level. To ...
>
- SLP (sleep)
-- When ANT is in operation, this line is stayed at H lev...
>
- SUP (suspend)
-- As the ANT module is in use, this line is at H level. ...
** Caution and E.T.C. [#b63f5047]
>
- Please do not deface the make of Technical Conformity a...
- Please do not modify and/or alter this module. Once you...
- The connector for the characteristic test antenna is on...
- BC-ANR-SERIAL uses lead-free solder. When you solder on...
>
About ANT communication, please look at http://www.thisis...
The specification document of ANT protocol is available a...
BC-ANT-SERIAL is equipped with nRF24AP2-8CH. 8 channels o...
* Revision History [#wa9f6990]
>
- 2013/01/31 This article is initially uploaded
End:
[[ANT]]
*BC-ANT-SERIAL [#l03c8002]
** 1. Overview [#m22dd705]
>
BC-ANT-SERIAL is a module that is equipped with nRF24AP2-...
>
&ref(DSCF7967r.JPG,,40%);~
※ ?100-yen coin is placed for the reference.
** 2. Specification [#iaa6231e]
>
- Absolute Maximum Ratings
||Minimum|Maximum|
|Supply Voltage (VDD)|-0.3V|+3.6V|
|GND Voltage (VSS)||0V|
|I/O Terminal Voltage|-0.3V|Less than 3.6V or VDD + 0.3V|
|Operation Temperature (No Condensation)|-40℃|+85&#...
|Storage Temperature (No Condensation)|-40℃|+85T...
>
- Operation Ratings
|Items|Minimum|Standard|Maximum|Unit ? Memo|
|Supply Voltage|1.9|3.0|3.6|V|
|H level Input Voltage|0.7 x VDD||VDD|V|
|L level Input Voltage|VSS||0.3 x VSS|V|
|H level Output Voltage|VDD ? 0.3||VDD|V|
|L level Output Voltage|VSS||0.3|V|
|Output Frequency|2403||2480|MHz (1MHz steps 78 waves)|
|PCB (Length)||26.5||mm|
|PCB (Width)||15||mm|
|PCB (Depth)||1||mm (Excluding parts)|
**3. Host Interface [#udec3c27]
>
To communicate with a microcontroler, BC-ANT-SERIAL suppo...
>
Assignment of pin-headers and pads are shown in the table...
>
- Assignment of Pin-Headers
|No.|Signal Type|Direction|Memo|
|1|VDD|Voltage|About Supply Voltage, Please look at ?2. S...
|2|GND|GND||
|3|RTS|Output|UART communication flow control|
|4|RX|Input|UART communication (Receiving at module side)|
|5|TX|Output|UART communication (Transmitting from module...
>
- Assignment of Pads
|Pad Name|Signal Type|Direction|Memo|
|RST|RESET|Input|Resetting ANT chip|
|SUP|SUSPEND|Input|Suspending ANT chip|
|SLP|SLEEP|Input|Sleeping ANT chip|
|BR1|BR1|Input|Configure UART communication speed1|
|BR2|BR2|Input|Configure UART communication speed2|
|BR3|BR3|Input|Configure UART communication speed3|
>
&ref(DSCF7962r2.JPG,,40%);
&ref(DSCF7963r2.JPG,,40%);~
>
The lines of RST, SUP, and SLP are used for tightly manag...
The lines of BR1, BR2, and BR3 are used for setting the s...
>
[Caution]~
In the picture, (a) is the connector, which is specifical...
In the picture, (b) is the chip antenna. To maintain the ...
***About Control Pads [#cce6d707]
>
The Size of RST, SUP, SLP, BR1, BR2, and BR3 pads is iden...
>
- RST
-- As ANT chip is electronically reset externally, this p...
>
- SUSPEND
-- This pad is used for suspending ANT chip. The line is ...
>
- SLEEP
-- This pad lets ANT chip sleep. This line is pulled-up t...
>
- BR1, BR2, and BR3
-- These lines are pulled-up to VDD. As no resistor is at...
>
-- Pads & Communication Speed
|BR1|BR2|BR3|Communication Speed (bps)|
|0|0|0|4800|
|0|0|1|38400|
|0|1|0|19200|
|0|1|1|50000|
|1|0|0|1200|
|1|0|1|9600|
|1|1|0|2400|
|1|1|1|57600|
0: 0Ω resistor is attached~
1: Non~
** How to Use [#u1755de7]
>
(1) How to connect with the serial communication (TXD, RX...
Pin-headers are attached at J1. Please look at Host Inter...
&ref(picture3.jpg,,60%);~
>
From ANT module, RTS is output for controlling hardware f...
>
(2) How to Connect Control Lines (Reset, Sleep, and Suspe...
&ref(picture4.jpg,,60%);~
~
To use the lines of RST (reset), SLP (sleep), and SUP (su...
>
- RST (reset)
-- When ANT is in operation, this line is at H level. To ...
>
- SLP (sleep)
-- When ANT is in operation, this line is stayed at H lev...
>
- SUP (suspend)
-- As the ANT module is in use, this line is at H level. ...
** Caution and E.T.C. [#b63f5047]
>
- Please do not deface the make of Technical Conformity a...
- Please do not modify and/or alter this module. Once you...
- The connector for the characteristic test antenna is on...
- BC-ANR-SERIAL uses lead-free solder. When you solder on...
>
About ANT communication, please look at http://www.thisis...
The specification document of ANT protocol is available a...
BC-ANT-SERIAL is equipped with nRF24AP2-8CH. 8 channels o...
* Revision History [#wa9f6990]
>
- 2013/01/31 This article is initially uploaded
Page:
![[PukiWiki]](image/bc_logo.png "[PukiWiki]"){kind=logo}
